dingli@dlbio-dryer.com +86 15333718778(Wechat/WhatsApp)
Time: 2023-08-11 Published: Alice

Ensure that the amount of ventilation of the sand dryer, keep track of the temperature inside the dryer, and accordingly the addition of fuel in order to achieve energy-saving drying state. Sand dryer ventilation, mainly in the dryer drying cylinder and hot air furnace between, it can use natural wind, but also can be artificial wind, and then the amount of wind blowing to the dryer's cylinder. The key parts to manage the exhaust air selling are the flap valve and flashing valve, operate these 2 parts well to ensure the exhaust air smoothly and well ventilated. First of all, we have to learn to judge the good and bad ventilation situation by ourselves. We use the simpler way, first of all, we wet our hands, and then extend the hand to the outlet, in this case, if after a while on the hands of the water is evaporated, it shows that the ventilation is good, and vice versa that the ventilation does not work, need to be adjusted. Of course, this is only the simpler and more effective way to determine.

sand dryers.jpg

Adjustment of ventilation we can be debugged in the following way:

1, we should pay attention to the flap between the leakage of the wind Qian situation, especially the bearing parts of the sealing situation. And prevent the flap valve fall in big more slag chunks, bricks, wire and other debris. Caused by deep wind, and even impede the discharge or stuck flap, can not be flipped.

2, observe the flap valve under the material more or less and under the material interval size, whether with the sludge dryer discharge speed compatible. Do not store too much material in the hopper to affect the discharge. And do not store too little material vibration shall be prosperous.

3, to the rotor shaft oil cup refueling on time. Screwed l ~ 2 times per shift, silver rotating a buckle can be. On the flash valve to observe whether the operation is flexible, whether the material is smooth, balance hammer position is appropriate, triangular cone and the material pipe mouth contact is tight.

According to the accumulation of ash under the material situation, you can adjust the balance hammer appropriate. The triangular cone is usually movably connected to the lever. In order to avoid flickering due to vibration and displacement, can also be aligned with the mouth of the downstream material pipe after it is fixed welded on the lever.

 

LEAVE US A MESSAGE

HOT CASES & PRODUCTS

Leave Us A Message

If you want to know the lowest price of equipment, configuration, production plan, etc., please leave us a message or contact us via WhatsApp/Wechat: +86 153-3371-8778

We will keep your information confidential

**

Old Customer Message

  • Mrs Rose*** 2023-08-20

    I would like to ask for a price of bio-organic fertilizer production line.

  • Mr Nicol*** 2023-09-18

    Hello. How much is your cow manure dryer? the one with 100 ton/day?

  • Mr Musta*** 2023-10-21

    Please send offer for bio fertilizer machine with all technicals spécifications

  • Mr Bong*** 2023-11-16

    We are in need of a chicken manure dryer to dry chicken manure.

  • Mr Geor*** 2023-12-11

    We are intrested in drum dryer for poultry manure, we need a high capacity.

  • Mr Kaml*** 2024-01-03

    We are interested in cow manure dryer-5 tons per hour .

  • Mr Gabr*** 2024-01-18

    Please send me more details about this bio fertilizer making product line.

  • Mr Boja*2024-02-26

    Interested in organic fertilizer making machine. what price and size it creates?

  • Mr Azha*** 2024-03-19

    Looking for a system to dry cow dung from 70 % moisture to 15 % moisture.

  • Mr Ngab*** 2022-04-23

    Im interested in machine to dry 5 t/h of cow manure

  • Mr Subh*** 2024-05-08

    Sand drying machine price and advise.

  • Mr Eric*** 2024-06-29

    Hello, I am writing to quote a biofertilizer production unit for 15 tons per hour.

  • Mr Rilw*** 2024-07-12

    Larvae dryer, Please can you send me your price list of your models?

LEAVE US A MESSAGE

Leave Us A Message To Get A Quote